New pages
Jump to navigation
Jump to search
- 10:08, 18 December 2017 Fast diagnostics enable/disable (hist | edit) [632 bytes] PRJ (talk | contribs) (Created page with "=== Enabling/disabling fast diag === By default fast diag is always enabled and streaming data, if you want to disable it (for example you want to use VCDS for pulling codes o...")
- 14:56, 14 December 2017 LC/NLS (hist | edit) [1,783 bytes] PRJ (talk | contribs) (Created page with "== Description == prjmod supports flatshift and launch control with antilag function.<br/> Launch control is implemented using ignition retard to build boost and either igniti...")
- 13:47, 14 December 2017 Map switching (hist | edit) [1,251 bytes] PRJ (talk | contribs) (Created page with "== Description == Map switching is done from the MFTS pin (pin 46).<br/> The current logic allows to switch the fuel and ignition maps, as well as gives an option to choose wh...")
- 18:57, 5 November 2017 Safety limits (hist | edit) [2,421 bytes] PRJ (talk | contribs) (Created page with "==Rev limit== ===Description=== The factory revlimiter is sequential fuel cut. With prjmod an ignition cut limiter is also provided. ===Maps=== *Rev limiter - fuel cut - start...")
- 18:41, 5 November 2017 Boost control (hist | edit) [1,460 bytes] PRJ (talk | contribs) (Created page with "==Algorithm== The boost controller is a fairly simple closed loop PID controller with a feed-forward map.<br/> ==Overboost== The overboost functionality is rather simple - fo...")
- 22:54, 2 November 2017 Idle control (hist | edit) [1,415 bytes] PRJ (talk | contribs) (Created page with "==Algorithm== Fast path idle control is done through ignition. Slow path idle control is done through a base lookup map, and then adaptive closed loop control.<br...")
- 00:06, 2 November 2017 Knock control (hist | edit) [5,736 bytes] PRJ (talk | contribs) (Created page with "==Working principles== ===Background=== The M2.3.2 ECU runs a bog-standard distributor based logic in the fuel/ign chip, except that it's output does not go directly to an ign...")
- 23:31, 1 November 2017 Ignition (hist | edit) [2,616 bytes] PRJ (talk | contribs) (Created page with "==Algorithm== Ignition is fairly straightforward, you can specify up to -22.5 degrees of retard in a map cell, or up to 168.75 of advance.<br/> It all gets added up and then o...")
- 16:18, 1 November 2017 Fuel (hist | edit) [8,274 bytes] PRJ (talk | contribs) (Created page with "== Introduction == In M2.3.2 LOAD is the injection time in milliseconds to reach lambda 1.<br/> Because rescaling all LOAD on every axis every time you change injectors is an...")
- 15:18, 1 November 2017 Speed Density (hist | edit) [2,742 bytes] PRJ (talk | contribs) (Created page with "== Algorithm == The MAP sensor is sampled crank-synchronously. Five times per cycle.<br/> <b>LOAD = FILTER((VE(MAP,RPM)*VE_MULT+VE_ADDEND)*MAP)</b>")
- 14:10, 1 November 2017 Toolchain setup (hist | edit) [2,106 bytes] PRJ (talk | contribs) (Created page with "== Initial setup == Download the following: * [http://www.tunerpro.net/ TunerPro RT] * [http://www.devtechnics.com/winlog.htm WinLog] or [https://www.14point7.com/pages/softwa...")
- 11:21, 1 November 2017 Realtime emulation (hist | edit) [1,288 bytes] PRJ (talk | contribs) (Created page with "== 27c512 == For the top board chip you can use any 8 bit emulator. I recommend the Moates Ostrich due to native TunerPro support. == 87c257 == Here it is a little more compl...")
- 00:38, 1 November 2017 Requirements and modifications for running prjmod (hist | edit) [4,133 bytes] PRJ (talk | contribs) (Created page with "==MAP sensor== You need the MPXH6400A MAP sensor. It is possible to use any sensor, but unless you need to run more than 2.8 bar boost, save yourself the trouble, and run the...") originally created as "Modifications for running prjmod"
- 23:51, 31 October 2017 Hardware limitations (hist | edit) [2,726 bytes] PRJ (talk | contribs) (Created page with "=== RPM limit === The fast diag puts quite a bit of strain on the boost/knock processor, which is already very strained.<br/> It is possible to modify the code, but the curren...")
- 23:32, 31 October 2017 Prjmod features (hist | edit) [455 bytes] PRJ (talk | contribs) (Created page with "The following list of features is currently implemented: * Speed Density fueling strategy (MAF not used) - complete rewrite of load acquisition from scratch * Full support for...")